Sixty-one gauges, fixtures and machines.

• Can be supplied for through bore / blind bore applications
• Adjustable depth collars can be provided for checking a specific depth
• Range: 2 mm to 200 mm
• Hard chrome plated
• Through / blind /step bore
• Two setting rings required

• Range: 10mm to 180 mm Middle
• Two setting masters required
• Offered with Snap Gauge with jet fixed in Carbide tip
• Please specify the unit for which Air snap gauge is required

• Two Jet Air Ring Gauge to check outside diameter, Taper & Ovality
• Three jet Air Ring Gauge for detecting Lobbing effect @ 120 Degrees
• Can be supplied with Tungsten Carbide wear rings on request
• Air Ring gauge - above dia. 150 mm available on request

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

• High pressure system - High speed of response and self cleaning of gauging area ensures accurate reading of size, taper and ovality at a time
• Non-contact Gauging - Long life due to minimal frictional wear
• Two Setting Masters - Ensures correct magnification of reading at all times
• System Pressure Check Gauge - provides a constant check on the system pressure i.e 3 bars (45 psi), regulated by a high precision regulator built in to the unit
• Minimum line pressure required 4.5 bars (67 psi)

• Differential back pressure sensing
• Simplicity, Robust construction and ease of use combined with accuracy gives the confidence on the shop floor
• Easy setting with a single control
• Self centering gives speed and accuracy in dimensional measurement
• No special training needed
• Fixed Magnification
• Two setting masters ensure correct linear setting
• Large-scale diameter of 115 mm for clear visibility. Wider measuring ranges

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

• Air electronic convertor complete with air drier &
• Filter set
• Vertical Bar Graph (Tri Colour/Red/Umber/Green) &
• Red Six digit display
• Absolute/ Comparative Measurement
• Auto calibration Facility
• 4 different setting parameters stored
• Metric/Inch Measurement

• Tri Colour Six digit display(ok/not ok/rework)
• Absolute / Comparative Measurement
• Auto calibration Facility
• Metric/Inch Measurement
• Static/Dynamic measurement
• RS 232 Output
• Relay Output 25 V
• Single Tricolour Led for component tolerance status

• Tri Colour Six digit display(ok/not ok/rework)
• Absolute / Comparative Measurement
• Auto calibration Facility
• Metric/Inch Measurement
• Static/Dynamic measurement
• RS 232 Output
• Relay Output 24 V

• LVDT probe selection provided with 8 results of various combination
• SPC (Statistical Process Control) facility for monitor a process for confirming product with minimum waste
• 7'' graphic color display
• 30 different user programmable fixture programs with programmable fixture name and result name
• Interface USB plug port
• Interaction with Standard PC USB keyboard Interface
• Pendrive interfacing
• Data seen on computer or laptop with the help of pen drive without any software

• SPC (Statistical Process Control) facility for monitor a process for confirming product with minimum waste
• 7'' graphic color display
• 50 different user programmable fixture programs with programmable fixture name and result name
• Interface USB plug port
• Pendrive interfacing
• Facility to display up-to 8 results
• Statistical Analysis Runchart, cp-cpk, Histogram, etc
• Analysis are provided for each individual result and allover accept, rejectt status

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for Universal Ball Joint with SPC Software & Report Generation
• Checking 6 window width & stagger HT
• Pick & place gripper arrangement for automatic part handling
• Automatic Measurement Cycle
• Motorised part rotation for window orientation with special sensor
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility
• Automatic accpet & reject part segragation

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for Bearing Shaft Of Different Length
• Checking bearing dia at 2 places, sleeve dia, C-length & total length
• Pick & place gripper arrangement for automatic part handling
• Automatic Measurement Cycle
• Dynamic reading & automatic recording of all readings
• Memory module for part saving
• Automatic accpet & reject part segragation

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for Camshaft with SPC Software & Report Generation
• Checking 6 Journal Dia at 3 Places & Linear Distance
• Common Fixture arrangement for Exhaust & Intake Camshaft with Just Center Change
• Automatic Measurement Cycle
• Motorised Part Rotation
• Dynamic reading & automatic recording of all readings
• Dia, Taper, ovality, Runout, concentricity, Face Runout, Cylindricity
• Report E-Mail Facility

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for Differential Case with SPC Software & Report Generation
• Checking key parameters
• After gauging accept automatic laser marking with alpha-numeric & 2D code
• 2D code automatic reader interfacing with verification
• Automatic Measurement Cycle
• Motorised Part Rotation
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for Rear Axle with SPC Software & Report Generation
• Checking key parameters
• After gauging accept automatic laser / dot pin marking with alpha-numeric & 2D code
• Automatic Measurement Cycle
• Motorised Part Rotation
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for End Cover with SPC Software & Report Generation
• Checking key parameters
• Measurments data recorder against the 2D datamatrix code scanned by the 2D datamatrix code reader
• Automatic Measurement Cycle
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for Heat Sink Flatness SPC Software & Report Generation
• Checking key parameters & flatness
• Measurments data recorder against the 2D datamatrix code scanned by the 2D datamatrix code reader
• Automatic Measurement Cycle
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility

• PLC-PC Based Electronic Contact Type Auto-gauging Machine for Output Shaft with SPC Software & Report Generation
• Checking OD diameters, ovality & runout
• Common machine for 7 different models
• Mitsubishi q series PLC with Proface HMI
• Pneumatics from SMC
• Automatic Measurement Cycle
• Rejection box interlock
• Bldc Oreintal Motorised Part Rotation

• Air -Electronic Contact Type gauging Machine for Bearing Cup & Taper Roller Beraing with SPC Software & Report Generation
• Checking OD diameters, ovality
• Checking taper roller bearing ID
• Pairing of cup & roller bearing
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility

• PLC-PC Based Electronic Contact Type Semi Automatic Multi -gauging Machine for Ring with SPC Software & Report Generation
• Checking ID, OD, Radial Thickness, Width, ID ovality, parallelity, No Of Teeth Counting
• Adjustable Fixture arrangement for Dia 250 MM to 500 MM
• Automatic Measurement Cycle
• Motorised Part Rotation
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility
• All Reading Data Recorded

• PLC-PC Based Electronic Contact Type Semi Automatic Multi -gauging Machine for Flex Plate with SPC Software & Report Generation
• Checking ID, OD, Thickness, Width, ID ovality, parallelity, No Of
• Automatic Measurement Cycle
• Motorised Part Rotation
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility
• All Reading Data Recorded

• PLC-PC Based Electronic Contact Type Semi automatic Multi -gauging Machine for Ring with SPC Software & Report Generation
• Checking ID, OD, Radial Thickness, Width, ID Ovality, parallelity, No Of Teeth Counting
• Adjustable Fixture arrangement for Dia 250 MM to 500 MM
• Automatic Measurement Cycle
• Motorised Part Rotation
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility
• All Reading Data Recorded

• Electronic Contact Type Multi gauging Machine for Inertia with SPC Software & Report Generation
• Checking ID, OD, groove dia, HT
• Motorised part rotataion
• Automatic measurement cycle
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility
• Electronic Contact Type gauging Machine for Hub with SPC Software & Report Generation
• Checking ID, OD, linear distance, HT

• Electronic Contact Type gauging Machine for Gear with SPC Software & Report Generation
• Checking ID, OD, mounting distance, lugs HT
• Motorised part rotataion
• Automatic measurement cycle
• Dynamic reading & automatic recording of all readings
• Report E-Mail Facility
• Gantry inetrface done for part loading & unloading

• Electronic Contact Type gauging & Marking Machine for Break Disc
• Dish thickness variation radialy & circumferentially, runout of top & bottom face checked
• Motorised part rotataion
• Automatic measurement cycle
• Dynamic reading & automatic recording of all readings
• After measurement completed part treaceability no with dimension marked with CNC dot pin marking machine
• Https://www.youtube.com/watch?v=yfoWcHqNc_A

• PLC-PC Based Electronic Contact Type gauging Machine for Engine Valve with SPC Software & Report Generation
• Checking Stem Dia at 2 Places, Head Dia, Groove Dia
• Common Fixture arrangement for Exhaust & Intake Valve with Just Probe Setting
• Automatic Measurement Cycle
• Motorised Part Rotation
• Dynamic reading & automatic recording of all readings
• Dia, Taper, ovality, Runout, concentricity, Face Runout, Cylindricity
• Report E-Mail Facility

• PC Based Electronic Contact Type Multi-gauging fixture for Camshaft with SPC Software & Report Generation
• Checking 6 Journal Dia at 2 Places & 3 Linear Distance
• Common Fixture arrangement for Exhaust & Intake Camshaft with Just Center Change
• Dynamic reading & automatic recording of all readings
• Dia, Taper, ovality, Runout, concentricity, Face Runout
• Report E-Mail Facility
• All Reading Data Recorded against Unique Sr. No which is entered automatically through Cognex 2 D Reader
• Probe Box LVDT Module Separately with Future Add On Facility

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

• PLC-PC Based Electronic Auto -gauging Machine for Gear to check ID, OD, Height, Concentricity, OD Run out, Face Run out
• Inbuilt SPC Software
• Automatic Measurement Cycle
• Job Loading / Unloading Automatic Interface with Customer Gantry System
• Pneumatic Slide Mounted Gauging Assembly for Measurement from Back Side
• Automatic Data Recording
• Software based Autosensing for Cycle Start Stop
• PLC with HMI for Auto-Manual Cycle

• PC Based Electronic Multi-gauging fixture for Vane Bottom Face & Side Face Flatness, Thickness & Width
• Inbuilt SPC Software
• Checking 12 Parameters within less than 10 Sec
• Pneumatic Slide Mounted Top Gauging Assembly for Measurement from Top Side
• Automatic Data Recording
• Software based Autosensing for Cycle Start Stop

• PC Based Electronic Multi-gauging fixture for Round Part
• Inbuilt SPC Software
• Checking 12 Parameters within less than 10 Sec with Part Rotation
• ID at top & bottom
• OD at top & bottom
• Taper of ID & OD
• Ovality of ID & OD at 2 Levels
• OD to ID Concentricity at 2 Levels

• Electronic Multi-gauging fixture for Sprocket
• Checking 3 Parameters within less than 12 Sec
• ID, OD, HT
• Automatic Cycle Controller by Micro Controller
• Unit
• OK / reject Paint Marker integrated with DRO Unit for automatic Part Paint marking
• Poka Yoke for confirmation of rejectted Component placed in rejecttion Bin
• Https://www.youtube.com/watch?v=o8NkdOSaDiE

• Electronic Multi-gauging fixture for Boss
• Checking 3 Parameters within less than 12 Sec
• ID, OD x 2, HT, hole PCD
• Automatic Cycle Controller by Micro Controller
• Unit
• OK / rejectT Paint Marker integrated with DRO Unit for automatic Part Paint marking
• Poka Yoke for confirmation of rejectted Component placed in rejecttion Bin
• Electronic Adjustable type Multi-gauging fixture for Pin

• Electronic Multi-gauging fixture for Boss
• Checking 7 Parameters
• OD X 2, collar OD, Ht, concentricity
• Automatic Cycle Controller by Micro Controller
• Unit
• Poka Yoke for confirmation of rejectted Component placed in rejecttion Bin & Rework in Rework Bin
• PLC with HMI
• SPC Software inbuilt with Reading Data recording

• Electronic Gauging System to check Pulley Distance & Runout
• Poka- Yoke for different process parameter added in the System
• Cast OD checked first, sensor sense the Bush fitting & then only Cycle Start
• After Cycle Start Pulley Groove Distance & Runout displayed on LCD Display
• If both the parameter are OK Pneumatic OK Punch cylinder punch the Component
• If any one parameter is not within the limit Tower Lamp with Buzzer sounds
• De-clamp the Comp manually
• Place the comp in rejectted bin sensed by Sensor if not placed next Cycle will not start

• Tri-ColorSix digit display
• 2 /3 /4 Dia ID / OD measurement
• Absolute / Comparative Measurement
• Auto calibration Facility
• Metric/Inch Measurement
• Static/Dynamic measurement
• RS 232 Output
• Relay Output 24 V

• Tri-Color Six digit display
• 6 OD Dia Measurement
• Absolute / Comparative Measurement
• Auto calibration Facility
• Metric/Inch Measurement
• Static/Dynamic measurement
• RS 232 Output
• Relay Output 24 V Optional

• Tri-Color Six digit display
• 6 Liner ID Dia Measurement in X Axis at 3 Levels & Y Axis At 3 Levels
• Absolute / Comparative Measurement
• Auto calibration Facility
• Metric/Inch Measurement
• Static/Dynamic measurement
• RS 232 Output
• Relay Output 24 V Optional

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

• Electronic Contact type Multigauging System
• Squareness wrt resting Face
• Dia of Component
• Taper of Component
• 2 Collar Lengths
• Precision Lm Guide for Inspection
• LCD Display Unit with Individual Status indication for each Parameter

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

• Adjustable type Run out Checking & Straightening Fixture on Hydraulic Press
• Run out at 2 End Reference diameter will be checked by resting the Parts on Bearing V Rest
• Adjustable for Variable Diameter & Length
• Run out checking arrangement can be adjusted as per diameter requirement
• Once the Run out being checked Bend of shaft can be corrected on same Fixture with the Help of Hydraulic Press

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

• Precise Mechanical Dial Type Dop ( Obd )Gauge Range 30-200 mm

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

Full specification available on request — send us the component drawing and we will come back with the gauging approach.

• Multi-parameter measurement in a single cycle
• PC based with live result display
• Automatic measurement cycle
• Accept / rejectt indication
• SPC data recording and report generation

• Simultaneous measurement of multiple parameters
• Built for high-precision inspection of housing components
• Repeatable results across production volumes
• PC based with on-screen result display
• Dial indicators for setting and verification

• Parallelity and flatness checking on oil cooler assemblies
• Enclosed station with controlled measuring environment
• Multi-point contact measurement
• On-screen result display with accept / rejectt status

• 30-watt fiber laser source
• 150 mm lens with 550 mm axis
• Control card with EzCad software
• Oem galvo and beam combiner
• Red light pointer for positioning
• Metal and plastic marking, barcode, QR and serial numbers
• Supplied with assembled PC — i3, 4 GB RAM, 120 GB SSD
• Maintenance free, long life

• Measures three parameters in one cycle
• Motorised part rotation for full-circumference measurement
• High accuracy and repeatability on critical shaft diameters
• PC based with live on-screen results
• Automatic measurement cycle

• Electronic contact type multigauging machine for inertia rings, with SPC software and report generation
• Checking ID, OD, groove dia and height
• Motorised part rotation
• Automatic measurement cycle
• Dynamic reading with automatic recording of all readings
• Report e-mail facility

• Electronic adjustable type multigauging fixture for pins
• Checking 5 parameters
• OD at two places and height
• Special tri-colour digital display unit
• Tower lamp for part status indication
• Diameter range 20 mm to 100 mm
• Length range 100 mm to 300 mm